Rust MAX3010x High-Sensitivity Pulse Oximeter and Heart-Rate Sensor for Wearable Health Driver

This is a platform agnostic Rust driver for the MAX3010x high-sensitivity pulse oximeter and heart-rate sensor for wearable health, based on the embedded-hal traits.

This driver allows you to:

• Get the number of samples available on the FIFO. See get_available_sample_count().
• Get the number of samples lost from the FIFO. See get_overflow_sample_count().
• Read samples from the FIFO. See read_fifo().
• Perform a temperature measurement. See read_temperature().
• Change into heart-rate, oximeter or multi-LED modes. See into_multi_led().
• Set the sample averaging. See set_sample_averaging().
• Set the LED pulse amplitude. See set_pulse_amplitude().
• Set the LED pulse width. See set_pulse_width().
• Set the sampling rate. See set_sampling_rate().
• Set the ADC range. See set_adc_range().
• Set the LED time slots in multi-LED mode. set_led_time_slots().
• Enable/disable the FIFO rollover. See enable_fifo_rollover().
• Clear the FIFO. See clear_fifo().
• Wake-up and shutdown the device. See shutdown().
• Perform a software reset. See reset().
• Get the device part and revision id. See get_part_id().
• Interrupts:
  • Read the status of all interrupts. See read_interrupt_status().
  • Set FIFO-almost-full level interrupt. See set_fifo_almost_full_level_interrupt().
  • Enable/disable the FIFO-almost-full interrupt. See enable_fifo_almost_full_interrupt().
  • Enable/disable the ambient-light-cancellation overflow interrupt. See enable_alc_overflow_interrupt().
  • Enable/disable the temperature-ready interrupt. See enable_temperature_ready_interrupt().
  • Enable/disable the new-FIFO-data-ready interrupt. See enable_new_fifo_data_ready_interrupt().

The device

The MAX30102 is an integrated pulse oximetry and heart-rate monitor module. It includes internal LEDs, photodetectors, optical elements, and low-noise electronics with ambient light rejection. The MAX30102 provides a complete system solution to ease the design-in process for mobile and wearable devices.

The MAX30102 operates on a single 1.8V power supply and a separate 3.3V power supply for the internal LEDs. Communication is through a standard I2C-compatible interface. The module can be shut down through software with zero standby current, allowing the power rails to remain powered at all times.

Datasheet:

• MAX30102

This driver should be compatible at least with the devices: MAX30102.

Usage

Please find additional examples using hardware in this repository: driver-examples

extern crate linux_embedded_hal as hal;
extern crate max3010x;
use max3010x::{Max3010x, Led, SampleAveraging};

fn main() {
  let dev = hal::I2cdev::new("/dev/i2c-1").unwrap();

  let mut sensor = Max3010x::new_max30102(dev);
  let mut sensor = sensor.into_heart_rate().unwrap();
  sensor.set_sample_averaging(SampleAveraging::Sa4).unwrap();
  sensor.set_pulse_amplitude(Led::All, 15).unwrap();
  sensor.enable_fifo_rollover().unwrap();

  let mut data = [0; 3];
  let samples_read = sensor.read_fifo(&mut data).unwrap();

  // get the I2C device back
  let dev = max30102.destroy();
}

Status

• Compatibility with MAX30102
• Compatibility with MAX30101
• Compatibility with MAX30105

Support

For questions, issues, feature requests, and other changes, please file an issue in the github project.

License

Licensed under either of

• Apache License, Version 2.0 (LICENSE-APACHE or http://www.apache.org/licenses/LICENSE-2.0)
• MIT license (LICENSE-MIT or http://opensource.org/licenses/MIT) at your option.

Contributing

Unless you explicitly state otherwise, any contribution intentionally submitted for inclusion in the work by you, as defined in the Apache-2.0 license, shall be dual licensed as above, without any additional terms or conditions.